-
Notifications
You must be signed in to change notification settings - Fork 6
/
printer.cfg
113 lines (108 loc) · 5.76 KB
/
printer.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
## Voron Design VORON2 350mm SKR 1.4 Turbo / TMC2209 UART config
## *** THINGS TO CHANGE/CHECK: ***
## MCU paths [mcu] section
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
## Z Endstop Switch location [homing_override] section
## Z Endstop Switch offset for Z0 [tmc2209 stepper_z] section
## stepper sense_resist & *_current [tmc2209 stepper_*] sections
## Probe points [quad_gantry_level] section
## Min & Max gantry corner postions [quad_gantry_level] section
## PID tune [extruder] and [heater_bed] sections
## Fine tune E steps [extruder] section
[include ./skr_1.4_pinmap.cfg]
[include ./huvud_pinmap.cfg]
[include ./main.cfg]
[include ./macros.cfg]
[include ./menu.cfg]
[include ./display.cfg]
[include ./steppers.cfg]
[include ./extruder.cfg]
[include ./bed.cfg]
[include ./fans.cfg]
[include ./sensors.cfg]
[include ./buttons.cfg]
# [include ./input_shaper.cfg]
[include ./vibration_macros.cfg]
[include ./shortcut_macros.cfg]
[include ./ercf_hardware.cfg]
[include ./ercf_macros.cfg]
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.055000, 0.015000, 0.035000, 0.027500, -0.017500, 0.010000, 0.017500, 0.037500, 0.055000, 0.072500, 0.072500
#*# 0.045000, -0.000000, 0.025000, 0.015000, -0.032500, -0.005000, 0.002500, 0.027500, 0.047500, 0.060000, 0.067500
#*# 0.042500, -0.010000, 0.020000, 0.010000, -0.037500, -0.007500, -0.005000, 0.020000, 0.045000, 0.055000, 0.055000
#*# 0.040000, -0.010000, 0.015000, 0.012500, -0.037500, -0.007500, -0.007500, 0.020000, 0.042500, 0.052500, 0.050000
#*# 0.035000, -0.007500, 0.017500, 0.010000, -0.040000, -0.007500, -0.005000, 0.017500, 0.035000, 0.047500, 0.047500
#*# 0.045000, 0.000000, 0.022500, 0.012500, -0.027500, 0.000000, 0.002500, 0.017500, 0.032500, 0.047500, 0.047500
#*# 0.045000, -0.007500, 0.022500, 0.010000, -0.040000, -0.015000, -0.007500, 0.012500, 0.037500, 0.052500, 0.050000
#*# 0.040000, -0.007500, 0.030000, 0.022500, -0.032500, -0.007500, -0.007500, 0.020000, 0.042500, 0.052500, 0.050000
#*# 0.045000, 0.007500, 0.037500, 0.025000, -0.020000, 0.005000, 0.012500, 0.030000, 0.060000, 0.067500, 0.065000
#*# 0.070000, 0.022500, 0.045000, 0.037500, -0.002500, 0.017500, 0.017500, 0.040000, 0.070000, 0.075000, 0.072500
#*# 0.072500, 0.025000, 0.047500, 0.045000, 0.002500, 0.022500, 0.030000, 0.050000, 0.067500, 0.080000, 0.087500
#*# tension = 0.2
#*# min_x = 50.0
#*# algo = bicubic
#*# y_count = 11
#*# mesh_y_pps = 4
#*# min_y = 50.0
#*# x_count = 11
#*# max_y = 300.0
#*# mesh_x_pps = 4
#*# max_x = 300.0
#*#
#*# [stepper_z]
#*# position_endstop = 3.478
#*#
#*# [bed_mesh high_temp]
#*# version = 1
#*# points =
#*# 0.180000, 0.160000, 0.132500, 0.100000, 0.080000, 0.067500, 0.075000, 0.090000, 0.125000, 0.147500, 0.167500
#*# 0.160000, 0.130000, 0.102500, 0.075000, 0.052500, 0.047500, 0.052500, 0.070000, 0.105000, 0.130000, 0.150000
#*# 0.142500, 0.112500, 0.095000, 0.057500, 0.037500, 0.027500, 0.027500, 0.050000, 0.085000, 0.105000, 0.125000
#*# 0.125000, 0.095000, 0.070000, 0.045000, 0.017500, 0.012500, 0.012500, 0.040000, 0.072500, 0.092500, 0.115000
#*# 0.107500, 0.080000, 0.060000, 0.027500, 0.007500, 0.002500, -0.002500, 0.017500, 0.050000, 0.072500, 0.090000
#*# 0.097500, 0.070000, 0.050000, 0.017500, 0.007500, 0.000000, 0.002500, 0.015000, 0.042500, 0.067500, 0.087500
#*# 0.095000, 0.062500, 0.045000, 0.010000, -0.007500, -0.017500, -0.017500, 0.005000, 0.035000, 0.060000, 0.082500
#*# 0.085000, 0.057500, 0.045000, 0.012500, -0.012500, -0.017500, -0.020000, 0.010000, 0.040000, 0.062500, 0.087500
#*# 0.092500, 0.065000, 0.055000, 0.015000, -0.005000, -0.010000, -0.012500, 0.012500, 0.045000, 0.065000, 0.087500
#*# 0.107500, 0.070000, 0.055000, 0.025000, 0.012500, 0.002500, -0.005000, 0.020000, 0.057500, 0.077500, 0.100000
#*# 0.122500, 0.082500, 0.070000, 0.035000, 0.017500, 0.010000, 0.005000, 0.032500, 0.055000, 0.080000, 0.112500
#*# tension = 0.2
#*# min_x = 50.0
#*# algo = bicubic
#*# y_count = 11
#*# mesh_y_pps = 4
#*# min_y = 50.0
#*# x_count = 11
#*# max_y = 300.0
#*# mesh_x_pps = 4
#*# max_x = 300.0
#*#
#*# [bed_mesh low_temp]
#*# version = 1
#*# points =
#*# 0.055000, 0.015000, 0.035000, 0.027500, -0.017500, 0.010000, 0.017500, 0.037500, 0.055000, 0.072500, 0.072500
#*# 0.045000, -0.000000, 0.025000, 0.015000, -0.032500, -0.005000, 0.002500, 0.027500, 0.047500, 0.060000, 0.067500
#*# 0.042500, -0.010000, 0.020000, 0.010000, -0.037500, -0.007500, -0.005000, 0.020000, 0.045000, 0.055000, 0.055000
#*# 0.040000, -0.010000, 0.015000, 0.012500, -0.037500, -0.007500, -0.007500, 0.020000, 0.042500, 0.052500, 0.050000
#*# 0.035000, -0.007500, 0.017500, 0.010000, -0.040000, -0.007500, -0.005000, 0.017500, 0.035000, 0.047500, 0.047500
#*# 0.045000, 0.000000, 0.022500, 0.012500, -0.027500, 0.000000, 0.002500, 0.017500, 0.032500, 0.047500, 0.047500
#*# 0.045000, -0.007500, 0.022500, 0.010000, -0.040000, -0.015000, -0.007500, 0.012500, 0.037500, 0.052500, 0.050000
#*# 0.040000, -0.007500, 0.030000, 0.022500, -0.032500, -0.007500, -0.007500, 0.020000, 0.042500, 0.052500, 0.050000
#*# 0.045000, 0.007500, 0.037500, 0.025000, -0.020000, 0.005000, 0.012500, 0.030000, 0.060000, 0.067500, 0.065000
#*# 0.070000, 0.022500, 0.045000, 0.037500, -0.002500, 0.017500, 0.017500, 0.040000, 0.070000, 0.075000, 0.072500
#*# 0.072500, 0.025000, 0.047500, 0.045000, 0.002500, 0.022500, 0.030000, 0.050000, 0.067500, 0.080000, 0.087500
#*# tension = 0.2
#*# min_x = 50.0
#*# algo = bicubic
#*# y_count = 11
#*# mesh_y_pps = 4
#*# min_y = 50.0
#*# x_count = 11
#*# max_y = 300.0
#*# mesh_x_pps = 4
#*# max_x = 300.0