Skip to content

Latest commit

 

History

History
157 lines (101 loc) · 5.55 KB

README.md

File metadata and controls

157 lines (101 loc) · 5.55 KB

Bain

Build Status

A DIY IoT wireless sensor for temperature, humidity and pressure. It is made of two parts:

  • Adafruit Feather HUZZAH with ESP8266: it's an Arduino compatible board that has WiFi capability and a connector to plug any Adafruit 3.7V Lithium polymer batteries. Note that any ESP8266 board should work.
  • Adafruit BME280 I2C or SPI: It's an environmental sensor with temperature, barometric pressure and humidity from Bosch.

This repository contains all the instructions to build the Bain sensor yourself.

Features

  • 🌡 Monitor temperature, pressure and humidity.
  • ✈ Data are sent to a custom MQTT broker as a JSON string.
  • 🕕 Time is syncronized every 6h with NTP and the timezone can be specified.
  • 😴 Deep sleep mode can be enabled to reduce power consumption. A standard LiPo battery of 1200 mAh can last about a week. Consumption is ~6.5mA while in deep sleep mode (optional).
  • 🔋 Monitor battery level (optional).
  • 💡 The source code is profusely commented and factorized. It should be easy to adapt to your needs.

Instructions

Assembly on a breadboard

Follow the connections shown below. There is 4 connections (blue, red, yellow and green) in between the Feather ESP8266 board the BME280 chip. And also a last connection in purple to enable deep sleep mode and reduce battery consumption (optional).

Warning: Apparently, the Feather ESP8266 chip can't be flashed with the purple connection so you have to disconnect it, then flash and then reconnect it.

Feather ESP8266

Flash the controller

Environement Setup

You should use the Arduino IDE to flash the controller to the board. Note that a VSCode extension for Arduino IDE is also available and works well.

  • You need to add the following URL to the Arduino Board Manager: http://arduino.esp8266.com/stable/package_esp8266com_index.json.

  • Then in the Arduino Board Manager, install the ESP8266 package. After this, you should be able to select the correct board from the Board Manager: Adafruit Feather HUZZAH ESP8266.

  • Then you need to install the following Arduino libraries (use the Arduino Library Manager):

Controller Configuration

  • Configure WiFi and MQTT credentials:

    • Copy bain/secret.h.template to bain/secret.h.
    • Edit bain/secret.h.
#ifndef BAIN_SECRET
#define BAIN_SECRET

#define WIFI_SSID "myssid"
#define WIFI_PASSWORD "mypassword"

#define MQTT_SERVER "your_server"
#define MQTT_PORT 1883
#define MQTT_CLIENT_ID "sensor1"
#define MQTT_MESSAGE_TOPIC "/bain_sensor/1"

// Leave blank to disable auth.
#define MQTT_USERNAME "your_username"
#define MQTT_PASSWORD "your_password"

#endif
  • Configure other parameters by editing bain/parameters.h.
#ifndef BAIN_PARAMETERS
#define BAIN_PARAMETERS

// Timezone
const int timeOffsetHours = -5;

// Delay between two measures in seconds.
const int loop_delay_s = 60;

// Enable deep sleep mode.
const boolean deep_sleep = true;

// Monitor battery level.
const boolean monitorBattery = true;

// LEDs. Disable by setting value to `-1`.
// Warning: Unused at the moment.
const int state_LED = -1;

#endif

Upload Firmware

Now you're ready to flash the controller.

  • From you editor, open bain/bain.ino.
  • Compile it.
  • After connecting the board to your computer, upload the controller.

By reading on the serial port, you should see logging messages about WiFi, the sensor and also the JSON string sent to the MQTT broker:

{
  "temperature": 25.23,
  "pressure": 1018.4,
  "humidty": 90.12,
  "timestamp": "2019-02-15 15:45:23",
  "batteryLevel": 82.3,
  "batteryCharging": false,
  "batteryVoltage": 3.76
}

Battery Level Monitoring

If you want to monitor the LiPo battery level, you need to add some connections to your circuit as shown below. For this you need the following parts:

  • 1 x 10 kΩ resistor
  • 1 x 47 kΩ resistor
  • 1 x 1 MΩ resistor
  • 1 x 1 µF capacitor

Feather ESP8266

Then you need to set monitorBattery to true in bain/parameters.h.

This setup comes from https://github.com/lobeck/adafruit-feather-huzzah-8266-battery-monitor.

Final Assembly

Once you've checked your assembly works you can solder everything together using a FeatherWing proto board. Here is the final assembly diagram:

Bain Final Assembly

Case

TODO.

Home Assistant

If your MQTT broker is connected to an Home Assistant instance, Bain sensors should be automatically discovered.

License

MIT.

Author