Skip to content

Generic embedded C driver to work with Sensirion's SEN5x environmental sensor modules via I2C

License

Notifications You must be signed in to change notification settings

Sensirion/embedded-i2c-sen5x

Repository files navigation

Sensirion Embedded I2C SEN5x Driver

This is a generic embedded driver for the Sensirion SEN5x sensor modules. It enables developers to communicate with the SEN54/SEN55 sensor module on different hardware platforms by only adapting the I2C communication related source files.

Supported sensors

  • SEN50 (only particulate matter signals available)
  • SEN54 (no NOx signal available)
  • SEN55 (full feature set)

Getting started

Connecting the Sensor

Your sensor has the five different connectors: VCC, GND, SDA, SCL, SEL (the sixth connector will not be used for now).

Pin Name Description Comments
1 VCC Supply Voltage 5V ±10%
2 GND Ground
3 SDA I2C: Serial data input / output TTL 5V and LVTTL 3.3V compatible
4 SCL I2C: Serial clock input TTL 5V and LVTTL 3.3V compatible
5 SEL Interface select Pull to GND to enable I2C interface
6 NC Do not connect

Implement the I2C Interface

So we need to adjust two files according to your platform.

Edit sensirion_i2c_hal.c

This file contains the implementation of the sensor communication, which depends on your hardware platform. We provide function stubs for your hardware's own implementation. Sample implementations are available for some platforms: sample-implementations. For Linux based platforms like Raspberry Pi you can just replace the unimplemented HAL template with the implementation in sample-implementations/linux_user_space/:

cp sample-implementations/linux_user_space/sensirion_i2c_hal.c ./

Edit sensirion_config.h

Skip this part for Linux based platforms since everything is already setup for this case.

Otherwise you need to check if the libraries <stdint.h> and <stdlib.h> are provided by your toolchain, compiler or system. If you have no idea on how to do that you can skip this step for now and come back when you get errors related to these names when compiling the driver. The features we use from those libraries are type definitions for integer sizes from <stdint.h> and NULL from <stdlib.h>. If they are not available you need to specify the following integer types yourself:

  • int64_t = signed 64bit integer
  • uint64_t = unsigned 64bit integer
  • int32_t = signed 32bit integer
  • uint32_t = unsigned 32bit integer
  • int16_t = signed 16bit integer
  • uint16_t = unsigned 16bit integer
  • int8_t = signed 8bit integer
  • uint8_t = unsigned 8bit integer

In addition to that you will need to specify NULL. For both we have a detailed template where you just need to fill in your system specific values.

Now we are ready to compile and run the example usage for your sensor.

Compile and Run

Pass the source .c and header .h files in this folder into your C compiler and run the resulting binary. This step may vary, depending on your platform. Here we demonstrate the procedure for Linux based platforms:

  1. Open up a terminal.
  2. Navigate to the directory where this README is located.
  3. Run make (this compiles the example code into one executable binary).
  4. Run the compiled executable with ./sen5x_i2c_example_usage
  5. Now you should see the first measurement values appear in your terminal. As a next step you can adjust the example usage file or write your own main function to use the sensor.

Background

Files

sensirion_i2c.[ch]

In these files you can find the implementation of the I2C protocol used by Sensirion sensors. The functions in these files are used by the embedded driver to build the correct frame out of data to be sent to the sensor or receive a frame of data from the sensor and convert it back to data readable by your machine. The functions in here calculate and check CRCs, reorder bytes for different byte orders and build the correct formatted frame for your sensor.

sensirion_i2c_hal.[ch]

These files contain the implementation of the hardware abstraction layer used by Sensirion's I2C embedded drivers. This part of the code is specific to the underlying hardware platform. This is an unimplemented template for the user to implement. In the sample-implementations/ folder we provide implementations for the most common platforms.

sensirion_config.h

In this file we keep all the included libraries for our drivers and global defines. Next to sensirion_i2c_hal.c it's the only file you should need to edit to get your driver working.

sensirion_common.[ch]

In these files you can find some helper functions used by Sensirion's embedded drivers. It mostly contains byte order conversions for different variable types. These functions are also used by the UART embedded drivers therefore they are kept in their own file.