Pioneer AVR (asyncio)

Home Assistant media_player custom integration for Pioneer AVRs. Inspired by the original Pioneer integration. Connects to a network capable AVR that supports the Pioneer API, typically used in pre-2016 Pioneer AVR models. Developed and tested on a VSX-930 (with Main Zone and HDZone outputs), and on other models by the community.

This integration supports the following features (not all features are supported by all AVR models):

• Control power, volume and mute for zones available on the AVR
• Select the active input source for each available zone, which are detected from the AVR
• Set the tuner band and frequency, and select tuner presets
• Set audio parameters such as listening modes, tone and channel levels
• Set amp, DSP and video parameters

Installation

This integration can be installed via HACS by adding this repository as a custom repository. See the HACS documentation for the procedure.

Adding an instance

Warning

As of 0.9.0, support for YAML configuration via configuration.yaml is no longer supported. The configuration is ignored and an error is logged if YAML configuration is detected.

This integration is configured via the UI. Once installed, add an instance for the AVR in Home Assistant by navigating to Settings > Devices & Services > Integrations > Add Integration and searching for Pioneer AVR. (Note that the Pioneer integration is the original integration built into Home Assistant)

The following options that configure the connection to the AVR are available from the initial setup page:

Option	Default	Function
Device name	Pioneer AVR	Default base name for the AVR
Host	avr	DNS name/IP address for AVR to be added
Port	8102	Port to be used to communicate with the AVR API. Use port 23 if your AVR doesn't respond on the default port
Query sources from AVR	on	Query the list of available sources from the AVR when Next is clicked. See AVR sources
Maximum source ID	60	The highest source ID that will be queried when querying available sources from the AVR. See AVR sources
Don't check volume when querying AVR source	AVR default	Don't query zone volume when determining whether a zone is present on the AVR. Enable if zones on your AVR are not all detected

Once the integration is successfully added, devices representing the AVR and each supported zone are created, along with entities that are registered to the devices. The main entities are the media_player entities corresponding to each discovered zone that are used to control the basic functions for the zone: power, volume and mute.

Some AVRs have a maximum simultaneous connection limit, and will refuse to accept further connection requests once this limit is reached. Each instance of this integration uses one connection to the AVR, and each instance of the Pioneer iControlAV5 application will use another connection. For example, if iControlAV5 is open on two phones, then two connections will be in use.

NOTE: Some AVR device attributes (such as firmware version) are only available after the AVR main zone is powered on for the first time after the integration is added.

Instance options

After an instance is added, options that modify how the integration operates can be changed by clicking Configure on the appropriate instance on the integration's Hubs page. The available options are described in the subsections below.

Basic options

Option	Default	Function
Query sources from AVR	off	Query the list of available sources from the AVR when Next is clicked. See AVR sources
Maximum source ID	60	Highest source ID that will be queried when querying available sources from the AVR. See AVR sources
Manually configured sources		List of all input sources available on the AVR. See AVR sources
Scan interval	60s	Idle period between full polls of the AVR. Any response from the AVR (eg. to signal a power, volume or source change) will reset the idle timer. Some AVRs also send empty responses every 30 seconds, and these also reset the idle timer and prevent a full poll from being performed. Set this to 0 to disable polling
Timeout	5s	Number of seconds to wait for the initial connection and for responses to commands sent to the AVR. Also used to set the TCP connection idle timeout
Command delay	0.1s	Delay between commands sent to the AVR. Increase the delay if you are experiencing errors with basic commands that are sent to the AVR

Zone options

Option	Default	Function
Available sources for zone	all	List of sources available for selection as input for each zone. Use this option to limit the sources available for a zone in accordance with your AVR's capabilities. If no sources are specified, then all available sources as configured in Basic options are made available
Don't create entities for zone	off	Disable the creation of entities for a specific zone. Used when the integration detects a zone that does not exist for your AVR

Advanced options

These options enable functionality and workarounds that are required for some AVR models. Some of these are enabled by default for specific AVR models when these are detected by the integration.

The Advanced options page is shown only if Advanced Mode is enabled in the user's Home Assistant profile.

Option	Default	Function
Query basic AVR parameters only		Disable AVR queries for additional parameters (audio, video, amp, DSP, tuner, channel levels) which may not be supported on some AVR models
Workaround for Zone 1 initial volume reporting		Enable this workaround on AVRs that do not report the correct volume when the main zone is turned on and an initial volume is configured
Don't check volume when querying AVR source		Don't query zone volume when determining whether a zone is present on the AVR. Enable if zones on your AVR are not all detected
Step volume up/down to set volume level		Emulate volume level set by stepping volume up/down on AVR models that cannot set the volume level to a specific level
Maximum volume units for Zone 1	185	The highest volume unit for Zone 1
Maximum volume units for other zones	81	The highest volume unit for other zones
Extra aiopioneer parameters		Additional config parameters to pass to the aiopioneer package. See Extra aiopioneer params

Debug options

These options enable additional debugging to be output to the Home Assistant log. Debug level logging must also be enabled in Home Assistant for the integration to generate debug.

The Debug options page is shown only if Advanced Mode is enabled in the user's Home Assistant profile.

Option	Function
Enable listener task debug logging	(debug_responder parameter) Enables additional debug messages in the listener task
Enable responder task debug logging	(debug_responder parameter) Enables additional debug messages in the responder task
Enable updater task debug logging	(debug_responder parameter) Enables additional debug messages in the updater task
Enable command debug logging	(debug_responder parameter) Enables additional debug messages in the AVR command sending and command queue methods
Integration debug	Enables additional per-module debug messages in this integration

Enabling debugging

If the integration is not functioning as expected, then you will need to include the debug logging when logging an issue. See the Debug logs and diagnostics section in the Home Assistant Troubleshooting page for instructions for enabling debug logging for the integration and downloading the log.

Further module level debug logging for the integration can be enabled by adding entries in Integration debug configuration on the Debug options configuration page. The entries are in the format: _module_:_debug_level_. For example, config_flow:9 will enable full debugging output for the config_flow module. To enable full debugging for all modules, use *:9.

AVR sources

The integration saves a master list of available sources on the AVR, and a subset of these sources can be made available for selection as the zone's input source. On some models of AVR, some zones do not support the use of certain sources for input, and also some sources may only be selected on one zone.

The master list of sources can be queried from the AVR when adding an integration instance by enabling Query sources from AVR. They can also be re-queried when reconfiguring the integration instance from the Basic options page. To do this, enable the Query sources from AVR option then click Next. Note that the current list of sources will be replaced by the list returned by the AVR.

Source mappings in the master source list can be edited in the Basic options screen by removing unwanted mappings and adding extra mappings via the Manually configured sources option. Additional mappings can be added if your AVR does not automatically detect them. Each source mapping is in the form id:name, where id is a 2 digit identifier for the source (including a leading zero for single digit source IDs), and name is the friendly name for the source. You can rename a source mapping by removing the mapping and adding a new mapping with the same id.

Source IDs can be found in the aiopioneer documentation

On the Zone options page, the available sources for each zone can be selected. If no sources are selected for a zone, then all sources are made available for selection.

Extra aiopioneer parameters

Additional parameters can be configured in the Home Assistant integration and are passed to the aiopioneer packaged used by this integration for communication with the Pioneer AVR via its API. The parameters modify the package functionality to account for the operational differences between the various Pioneer AVR models. See aiopioneer documentation for a list of parameters that can be set.

Most configuration parameters are configurable via UI settings. Other parameters can be added through entries in the Extra aiopioneer parameters. Each entry is in the format parameter_name: value with value expressed in JSON format. For example, the am_frequency_step parameter can be set to 9 kHz by adding the entry am_frequency_step: 9.

Tuner entities

The entities below show the current tuner settings, and can also be used to change the tuner settings. These entities are available only when the tuner is selected as the input for a powered on zone.

Name	Type	Description
Tuner Band	select	Current tuner band (AM, FM)
Tuner AM Frequency	number	Current AM frequency (in kHz)
Tuner FM Frequency	number	Current FM frequency (in MHz)
Tuner Preset	select	Currently selected tuner preset, or unknown if no preset is. The preset is also reset to unknown when the frequency is changed

Entity attributes

media_player entity attributes

In addition to the standard media_player entity attributes, this integration exposes additional attributes for the Pioneer AVR:

Entity attribute	Type	Description
sources_json	JSON	JSON mapping of zone source names to source IDs
device_volume_db	float	Current volume of zone (in dB)
device_volume	int	Current volume of zone (in device units)
device_max_volume	int	Maximum supported volume of zone (in device units)

tuner_am_frequency entity attributes

The tuner_am_frequency number entity exposes the following additional attributes:

Entity attribute	Type	Description
am_frequency_step	int	The kHz step between valid AM frequencies. This value differs across regions. If not specified as a parameter, then this is calculated by stepping up and down the frequency when the band is first changed to AM

AVR properties (>= 0.9)

The following AVR properties are available as entities where supported and reported by your AVR model.

Caution

Property group entities are beta and may change in future releases as additional entities are created for individual properties.

Global AVR properties

Sensor entities for global AVR properties and property groups are registered to the parent device created for the AVR.

Property	Type	Description
Display	sensor	Current value shown on AVR front panel display
Speaker System	sensor	AVR speaker system currently in use
Amp	sensor	Amp property group, main sensor property: speakers
DSP	sensor	DSP property group, main sensor property: signal_select
Video Parameters	sensor	Video parameters property group, main sensor property: signal_output_resolution
Audio Parameters	sensor	Audio parameters property group, main sensor property: input_signal
Input Multichannel	binary_sensor	on if current input audio source is a multi-channel source

Zone AVR properties

Zone entities are registered to the zone device.

Property	Type	Description
channel_levels	sensor	Surround channel levels
tone	sensor	Tone setting, and bass and treble levels
Video	sensor	Zone video parameters property group
Audio	sensor	Zone audio parameters property group

Services (>= 0.7.3)

Service calls are used to invoke actions and change parameters on the AVR. They can be called from scripts, automations and UI elements, and can also be triggered via Developer Tools > Services.

Service set_tone_settings

Set AVR tone settings for zone.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
tone	string		Tone mode. See services.yaml for valid values (required)
treble	int	None	Tone treble value (-6dB -- 6dB)
bass	int	None	Tone bass value (-6dB -- 6dB)

Service set_tuner_band

Set AVR tuner band.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
band	string		Tuner band: AM or FM (required)

Service set_fm_tuner_frequency

Set AVR FM tuner frequency.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
frequency	float		Tuner frequency (87.5 MHz -- 108.0 MHz) (required)

Service set_am_tuner_frequency

Set AVR AM tuner frequency.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
frequency	float		Tuner frequency (530 -- 1700KHz) (required)

Service set_tuner_preset

Set AVR tuner preset.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
class	str		Tuner preset class (A -- G) (required)
preset	int		Tuner preset ID (1 -- 9) (required)

Service set_channel_levels

Set AVR level (gain) for an amplifier channel.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
channel	str		Tuner amp channel to modify. See services.yaml for valid values (required)

Service set_panel_lock

Set AVR panel lock.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
panel_lock	bool		Panel lock setting (required)

Service set_remote_lock

Set AVR remote lock.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
remote_lock	bool		Enable remote lock (required)

Service set_dimmer

Set AVR display dimmer.

Service data attribute	Type	Default	Description
entity_id	entity ID		Entity for AVR zone to modify (required)
dimmer	string		Dimmer mode. See services.yaml for valid values (required)

Service set_video_settings

To be implemented.

Service set_dsp_settings

To be implemented.

Service media_control

To be implemented.

Breaking changes

• 0.9
  Integration configuration via configuration.yaml is no longer supported. ADR10 outlines that integrations that communicate with devices, such as this one, must be configured via the UI. Also, several more recently added features, such as support for the HA device registry and dynamic integration loading/unloading, already do not work unless configured via the UI.

• 0.8
  The zone_h_sources and zone_z_sources params have been renamed to hdzone_sources, to be more consistent with the rest of the integration.

• 0.7
  The device_class for the zone entities has been updated to receiver. If any zone entities are exported to Google Assistant, this change currently (2023-01-08) removes the Google Home UI that was previously shown for this entity when using the default device_class of tv. You can restore the old behaviour by overriding device_class for the entity to tv, see Customising Entities for details on how to do this.

  The volume_step_delta config property has been deprecated upstream in crowbarz/aiopioneer and is no longer configurable from this integration.

• 0.6
  Zone entity unique IDs have changed to conform to unique ID requirements. Due to a bug with integration removal in previous versions, the entity IDs of your zones will probably change after upgrading to this version if you added the integration via the UI. To restore your entity IDs, perform the following steps:

  1. remove the integration via the UI (saving configuration settings).
  2. restart Home Assistant.
  3. in Home Assistant, navigate to Configuration > Entities and search for your Pioneer AVR zone entities. They should show a red exclamation mark in the Status column.
  4. select all the entities and click Remove Entity.
  5. reinstall the integration via the UI and restore configuration settings.

• 0.5
  volume_step_only logic has been rewritten to step the volume until the actual volume reaches (or exceeds) the desired volume. It will stop stepping and log a warning if after the step command the volume does not change or changes in the wrong direction.

• 0.4
  The AVR source query no longer skips source names that have not been renamed. This will result in additional sources being selectable. Specify sources manually to only allow certain sources to be selected.

• 0.3
  command_delay, volume_workaround and volume_steps have been moved into the params object. Additionally, volume_steps has been renamed volume_step_only and volume_workaround has been renamed to power_on_volume_bounce. You will need to update your configuration.yaml accordingly.

Implementation details

Under the hood, this integration uses crowbarz/aiopioneer to communicate with the Pioneer AVR via its API. Briefly, the features of this package are:

• Implemented in asyncio.
• Maintain single continuous telnet session to AVR, with automatic reconnect.
• Eliminate polling where AVR sends keepalive responses (on port 8102).

NOTE: On the VSX-930, the telnet API can become quite unstable when telnet connections are made to it repeatedly. The original integration established a new telnet connection for each command sent to the AVR, including the commands used to poll status. This integration establishes a single telnet connection when loaded, and re-connects automatically if it disconnects. The connection is used for sending commands, receiving responses, and receiving status updates which are reflected in Home Assistant in real time.