Discussions

• 1 You must be logged in to vote

  💬

  Set tool table commands give error 20

  samitray started Jun 7, 2024 in General

  

  

  1
• 1 You must be logged in to vote

  💬

  Two limits on each axis for STM32F446ZE with other interrupt inputs

  samitray started Jun 3, 2024 in General · Closed

  

  

  2
• 1 You must be logged in to vote

  🙏

  Port / Pin selection for multiple spindle

  samitray asked Jun 3, 2024 in Q&A · Unanswered

  

  

  0
• 2 You must be logged in to vote

  🙏

  Rigid Tapping G33.1 for Lathe and Milling

  hanifhan asked May 17, 2024 in Q&A · Unanswered

  

  

  

  

  4
• 1 You must be logged in to vote

  🙏

  Where in the code is G94 G1 XA feedrate situation assigned to X while A is coordinated to move with it

  bLouChip asked Jan 15, 2023 in Q&A · Answered

  

  

  

  

  39
• 1 You must be logged in to vote

  🙏

  Triggersequences with M62/M63

  AndreLukas121 asked May 23, 2024 in Q&A · Answered

  

  

  6
• 1 You must be logged in to vote

  🙏

  edge finding

  tcurdt asked May 28, 2024 in Q&A · Unanswered

  

  

  3
• 1 You must be logged in to vote

  🙏

  Alternative Interfaces to Step/Dir (CAN/RS485/Etc.)

  graykimchi asked May 26, 2024 in Q&A · Answered

  

  

  2
• 1 You must be logged in to vote

  🙏

  How can I use UART port on MKS Tinybee?

  ashokmanker asked Mar 3, 2024 in Q&A · Unanswered

  

  

  10
• 1 You must be logged in to vote

  🙏

  Y2 or M limit stop to work after upgraded.

  rmaltais asked May 20, 2024 in Q&A · Answered

  

  

  13
• 2 You must be logged in to vote

  🙌

  Devtronic SmartPendant - a way to control grblHAL based CNC machine without PC

  nickshl started Mar 17, 2024 in Show and tell

  

  

  

  

  18
• 1 You must be logged in to vote

  💡

  S-Curve - Jerk for Acceleration settings.

  Dietz0r started Oct 24, 2023 in Ideas

  

  

  

  

  23
• 1 You must be logged in to vote

  💬

  Uploading files to sd card not working

  SebastianMusser started May 21, 2024 in General

  

  

  4
• 5 You must be logged in to vote

  💡

  Web interface for building binaries

  terjeio started Oct 17, 2022 in Ideas

  

  

  

  

  408
• 1 You must be logged in to vote

  🙏

  How can I read the status of a pin via gcode?

  tcurdt asked May 20, 2024 in Q&A · Answered

  

  

  3
• 1 You must be logged in to vote

  💡

  M03 doesn't wait until rpm reached

  ToastyCH started Oct 2, 2022 in Ideas

  

  

  

  

  15
• 1 You must be logged in to vote

  💡

  Test of subroutines and modal state save/restore (M70-M73)

  terjeio started May 17, 2024 in Ideas

  

  

  

  

  3
• 1 You must be logged in to vote

  💬

  G code conditional execution (possibly looping)

  andrewmarles started May 25, 2023 in General

  

  

  

  

  76
• 1 You must be logged in to vote

  🙏

  set machine origin to 0, or bit3, not working for $22

  bertabus asked May 11, 2024 in Q&A · Closed · Answered

  

  

  3
• 0 You must be logged in to vote

  💬

  STM32F4xx 25Mhz Flash emulation

  samitray started Apr 29, 2024 in General · Closed

  

  

  14
• 1 You must be logged in to vote

  🙏

  Srk mini e3 v3 drive

  caohuongls asked Apr 30, 2024 in Q&A · Unanswered

  

  

  1
• 1 You must be logged in to vote

  🙏

  Mach3 usb with 2nd probe [resolved]

  rmaltais asked Apr 23, 2024 in Q&A · Answered

  

  

  

  

  13
• 1 You must be logged in to vote

  💬

  Alarm 2 or Alarm1 when mist OFF (M9) [resolved]

  rmaltais started Apr 30, 2024 in General · Closed

  

  

  7
• 1 You must be logged in to vote

  💬

  STM32F1xx C axis signals

  samitray started Apr 26, 2024 in General · Closed

  

  

  2
• 1 You must be logged in to vote

  💬

  How to configure TMC5160 on MKS Tinybee?

  ashokmanker started Apr 24, 2024 in General

  

  

  8