Skip to content

Turn the Arduino Due into a host-driven sensing and actuator platform

License

Notifications You must be signed in to change notification settings

l-mb/GPIO_Platform

Repository files navigation

GPIO_Platform

Turning an Arduino Due into a multi-channel data logger and signal generator driven via USB.

Summary

This firmware turns the Arduino Due into a multi-channel data logger and signal generator. The goal is to allow the host to do what it is good at (number crunching, FFT, displaying GUIs, data storage, that sort of boring stuff) while utilizing what the Arduino Due is really good for: an incredibly cheap, yet powerful., sensor and actuator platform.

This is a firmware that allows the periodic sampling of IO channels on the Due, and to report the values to the host. You can easily set up to have a port monitored at 100 Hz, for example. Or to report (interrupt-driven) whenever a specific digital PIN changes state, and the time between ticks. It supports several very simple filters for reporting data (averaging, delta values, etc) that are discussed in the command reference. The host doesn't have to poll, but can just set up a service for reporting data. (Of course, the ability to poll single reads is there.)

It also serves as a signal generator. The host doesn't have to supply a constant stream of writes; it can set up that a channel shall be periodically cycled through, say, a sine curve for analog outputs, flipping state for digital output pins ever so often, or a number of other things.

There is also a simple serial monitor for easy debugging by humans.

Warnings

This code is in its infancy. I wrote it to become more acquainted with the limitations and requirements on the Arduino Due platform. It is only a few days old and published now only because my New Year's leave is over. I very much welcome contributions, but if you're going to use this for production usage at this point in time, please be very, very careful. It's bound to change quite a bit.

Installation

  1. It is assumed that you have an Arduino Due and the Arduino environment installed, and are basically familiar with its operation.
  2. Install DueTimer from GitHub according to Ivan's instructions. GPIO_Platform uses DueTimer for it's scheduling.
  3. Download GPIO_Platform from GitHub
  4. Unzip the files and install into a sketch folder named GPIO_Platform
  5. Open the sketch via Arduino and verify, then download, the sketch to the Due.

Usage

GPIO_Platform is quite simple to use. Once it has booted, it awaits commands on the native USB port of the Due via serial. (The native port is used because it yields much higher performance; it ignores the serial baudrate and effectively runs at native USB 2.0 speed of 480 Mbps, if the Due and/or your host can keep up.)

The protocol is very simple. If you want to switch port 31 to output mode and then disable it, and read back it's value, here are the commands you'd issue:

pin d31 0
write D31 0
read k d31

Interface

Input

Note: the serial command monitor is very simplistic. Not just to use, but also in parsing. It does not echo back every command you enter, just once you press enter (and if debugging is enabled). It does not support anything like commandline editing.

It will accept, and attempt to parse and execute, a command once return ('\r') is received. The maximum length of a single commandline is 128 bytes.

If you want to resync or discard, hit backspace ('\b'). That will discard the entire command buffer and start from scratch.

Portnames

GPIO_Platform knows about descriptive port names, from d0 to d53, from a0 to a11, and DAC0 and Dac1. These are case-insensitive.

Do not specify numeric port ids.

In the future, this will be expanded to handle I²C, SPI and other addresses.

Output

GPIO_Platform does not produce a lot of output by itself, unless you enable debug mode. The main information that you are going to be interested in are the values read from the inputs.

These are reported in the following format: time key value

  • time is reported relative to the last reported value on the serial monitor in micro-seconds (that is, one millionth of a second)
  • key is a one character used to identify the respective source (specified when you configure it)
  • value the integer value read (or computed) for this source

Command reference

Input

read

Syntax: read key port

read k d31

Perform a one-shot read of the specified port number and report this back as a data point for key key. GPIO_Platform automatically knows whether to perform a digital or analog read.

source_add

Syntax: source_add key port period samples mode delta

Sets up a periodic polling of the given port, reporting the values under the respective keys.

period is also specified in micro-seconds. (e.g., to setup a source that is polled at a frequency of 1000 Hz, you'd specify a period of 1000). If 0, this port is not periodically polled, but only considered when this source is triggered via an interrupt.

port references the portname. If this is none, then this source is never read; this only makes sense for interrupt-driven sources. See source_attach_irq for details on which value is considered then.

If samples is not zero, GPIO_Platform will take this many samples into account before considering to report this value. This is an easy way to specify very simple filters. Staying with the example, if you had set a sampling frequency of 1000 Hz, and specified a value of 10 here, the filter would take a period of 1 centi-second into account. Which filter is applied is specified via the next flag.

mode only takes effect if samples is larger than 0.

  • If mode = 0, the computed value will simply be a sliding average over the period covered by the samples.
  • If mode = 1, the computed value will be an average over the sampling, but starting with a fresh buffer every time. This means that the computed value from this input will only be considered for reporting every samples count.
  • If mode = 2, the computed value will only be considered for reporting if all values agree. This is particularly useful for digital inputs for which it implies they must have been stable for the sampling period.

delta allows to cut down on reporting noise. The value (raw or computed) must have changed by at least this much since it was last reported before.

These filters are very simple and mainly useful for manual debugging. In practice, the processing (and thus filtering) power of the host computer is vastly superior to even the Arduino Due. Any filtering on the Due takes up processing power that could be spend reporting data.

Example:

// Create a source that reads the analog port 3 and reports its value
// every 1/10 second if it has changed at all:
source_add A a3 100000 0 0 1

// A source that reports if digital input 31 has been stable for at
// least 1 second, and changed since the last report:
source_add X D31 100000 10 2 1

source_attach_irq

Syntax: source_attach_irq key irq trigger count_ticks

Attach an interrupt-trigger to a source.

  • key refers to a previously configured source. Whenever this interrupt here triggers, that source is triggered for processing.
  • irq refers to the port that this interrupt handler should monitor.
  • trigger the trigger mode. If 0, the interrupt is triggered on a falling edge. 1 triggers on a rising edge. And 2 triggers on any state change.
  • count_ticks defines whether to count ticks since the last sampling period.
    • If set to 0 and the port on the source is 0, the source measures the µS between triggers (interval).
    • If set to 0 and the port on the source is set, the source samples the port whenever the interrupt triggers.
    • If set to 1, and the source has a non-zero period, the source will count the number of times the interrupt has triggered since the last period. This is an easy way to count pulses.
// Report the value of analog port 3 whenever digital pin 41 falls:
source_add A a3 0 0 0 0
pin d41 0
source_attach_irq A d41 0 0

// Count the number of times digital pin 31 is raised per second:
source_add D none 1000000 0 0 0
source_attach_irq D d31 1 1

// Something more complex. Report the average interval between state
// changes of pin 45, averaged over 8 samples each:
source_add C none 0 8 1 0
source_attach_irq C d45 2 0
// (Note that there is a catch here - *if* the final round of times
//  interrupt 45 triggers is less than 8 times, that last period is
//  never reported. There is currently no final timeout.)

source_del

Syntax: source_del key

Delete the given source.

Outputs

write

Syntax: write portname value

Write the value to the specified port. Digital or analog ports are automatically handled. For digital ports, any non-zero value is treated as HIGH.

output_add

Syntax: output_add key portname interval step offset mode pattern

Setup a periodic output pattern.

key is a unique identifier for this output. Note that this is a different namespaces from the source definitions.

port is the port this output will be written to.

interval specifies the interval between writes. This defines the output resolution and frequency.

step the step-size through the pattern buffer at every interval. Must be between 1 and the length of the pattern.

offset The starting point in the pattern buffer. Must be between 0 and the length of the pattern.

mode handles wrap-around. If 0, whenever the end of the pattern is reached, the pattern starts again from the beginning. If 1, the pattern direction is reversed, until the beginning is reached (and then again output from beginning to end).

pattern, finally, specifies the pattern to output to this port. GPIO_Platform has a few hardcoded output patterns for testing that can be used, but you can also upload patterns at runtime (eventually).

  • flip is a pattern consisting of just two entries; 0/LOW or 4095/HIGH. This can be used to easily switch a digital port on and off.
  • inc is a pattern consisting of 0 through 4095 and can be used to easily step a PWM or DAC output through all values.
  • sine outputs a pattern of 4096 values stepping a port through a sine curve centered at 2047. This is rather pretty with LEDs.

Examples:

// Flip a LED on pin 13 on and off every second:
output_add b d13 500000 1 1 0 flip

// If you have an RGB LED connected on PWM ports 2-4, this will cycle
// the colors through the sine curve at different speeds:
output_add r d2 500 1 0 0 sine
output_add g d3 1000 1 0 0 sine
output_add b d4 1500 1 0 0 sine
start

// And this one steps red and blue at the same time, but shifted by one
// half cycle - a bit like a police cruiser:
stop
clear
write d3 0
output_add r d2 1000 1 0 0 sine
output_add b d4 1000 1 0 2047 sine
start

pattern_list

List all available patterns.

output_del

Syntax: output_del key

Delete the given output.

output_reset

Reset all outputs to their starting offset.

Global commands

start

The start command enables the periodic timer. No output will be written or sources polled before this command is given.

stop

Stop all periodic in- and output.

clear

Wipe all configured sources and outputs.

Other commands

pin

Syntax: portname pin mode

Set the specified portname to the specified mode.

  • mode set to 0 corresponds to INPUT
  • mode set to 1 corresponds to INPUT_PULLUP
  • mode set to 2 corresponds to OUTPUT

help

Display all valid command names.

debug

Syntax: debug level

Set the debug level (between 0 and 2). 0 disables all debugging output and is intended for production use. 1 reports commands back. 2 enables more detailed internal logging, and you probably don't want to enable this.

dump

Dump the current configuration.

Notes

Be careful how many sources you monitor and poll. While this sketch tries to decouple the amount of work done in interrupt handlers, clearly even the Due is limited in processing power.

Currently, all sources and outputs are handled via one timer interrupt. That means that the timer interrupt needs to trigger at the greatest common divisor of all specified periods. If you specify a period of 1000 for one source, and 1001 for another output, you are going to overload the Due.

Copyright and License statement

Copyright (C) 2014 Lars Marowsky-Bree (lars@marowsky-bree.de)

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.

About

Turn the Arduino Due into a host-driven sensing and actuator platform

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages