Skip to content

ROS Compatible ground robots (2WD, 4WD, Ackermann Steering, Mecanum Drive)

License

Notifications You must be signed in to change notification settings

methylDragon/linorobot

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

linorobot Build Status

Linorobot is a suite of Open Source ROS compatible robots that aims to provide students, developers, and researchers a low-cost platform in creating new exciting applications on top of ROS.

Tutorial

You can read the full tutorial how to build your robot here.

Multiplatform

Supports multiple types of robot base:

  • 2WD
  • 4WD
  • Ackermann Steering
  • Mecanum drive

alt text

Works on:

  • ROS Indigo (Ubuntu 14.04)
  • ROS Kinetic (Ubuntu 16.04)

Hardware

Fabricate your own Teensy 3.1/3.2 shield,

alt textalt text

or wire it on your own. Wiring diagrams are also provided. alt text

Supported IMUs:

  • GY-85
  • MPU6050
  • MPU9150
  • MPU9250

The IMU drivers are based on i2cdevlib.

Supported Motor Drivers:

  • L298 (MAX: 35V, 2A)
  • BTS7960 (MAX: 24V, 43A)
  • Electronic Speed Controllers (ESC) w/ Reverse. This has been tested to control brushless motors used in RC cars and hoverboards.

Supported ROS Compatible Sensors:

  • XV11 Lidar
  • RPLidar
  • Intel RealSense R200
  • Kinect

Tested on Linux compatible ARM dev boards:

  • Raspberry Pi 3
  • Jetson TK1
  • Jetson TX1
  • Odroid XU4
  • Radxa Rock Pro
    **Technically this should also work with any ARM dev board at least (1GB RAM) that runs Ubuntu Trusty or Xenial.

Installation

alt text

git clone https://github.com/linorobot/lino_install && cd lino_install
./install <base> <sensor>

Firmware

Flexible and configurable components. linorobot_ws/teensy/firmware/lib/config/lino_base_config.h

Robot base configuration:

//uncomment the base you're building
#define LINO_BASE DIFFERENTIAL_DRIVE
// #define LINO_BASE SKID_STEER
// #define LINO_BASE ACKERMANN
// #define LINO_BASE MECANUM

IMU configuration:

//uncomment the IMU you're using
#define USE_GY85_IMU
// #define USE_MP6050_IMU
// #define USE_MPU9150_IMU
// #define USE_MPU9250_IMU

Motor driver configuration:

//uncomment the motor driver you're using
#define USE_L298_DRIVER
// #define USE_BTS7960_DRIVER
// #define USE_ESC

Motor configuration:

//define your robot' specs here
#define MAX_RPM 330               // motor's maximum RPM
#define COUNTS_PER_REV 1550       // wheel encoder's no of ticks per rev
#define WHEEL_DIAMETER 0.10       // wheel's diameter in meters
#define PWM_BITS 8                // PWM Resolution of the microcontroller
#define LR_WHEELS_DISTANCE 0.235  // distance between left and right wheels
#define FB_WHEELS_DISTANCE 0.30   // distance between front and rear wheels

Uploading the codes:

cd ~/linorobot_ws/src/linorobot/teensy/firmware
platformio run --target upload

Creating a Map

alt text

Launch base driver:

roslaunch linorobot bringup.launch

Launch mapping packages:

roslaunch linorobot slam.launch

Autonomous Navigation

IMAGE ALT TEXT

Launch base driver:

roslaunch linorobot bringup.launch

Launch navigation packages:

roslaunch linorobot navigate.launch

Packages

No packages published

Languages

  • C++ 97.9%
  • C 1.2%
  • Other 0.9%